Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 1 in stock

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Ignition pickup and tacho sensor

Connector plug has two male spades. Also known as phase sensor. Used on models with the large Marelli P8 ECU. No longer available from Guzzi. Note 90° angle where cable exits sensor. See ENA90141 for O ring used to fit this part

 1 in stock

 29721660 GU29721660 29 72 16 60
 2972 1660 2972.1660 29.72.16.60

Oil temperature sensor

See ELA03330 for sensor support

 1 in stock

 29724961 GU29724961 29 72 49 61
 2972 4961 2972.4961 29.72.49.61

2 pin superseal female block connector, used for main loom connections on modern models. See ELA70183 and ELA70184 for the connectors that go in these blocks. Use male connectors with this block

These are a high quality weathertight connector designed to keep corrosive elements out

 1 in stock

Ducati type alternator stator

300W output, doesn't include rotor / magnet. Also known as Guzzi ref. 30712460

 1 in stock

 37712405 GU37712405 37 71 24 05
 3771 2405 3771.2405 37.71.24.05

Brush kit for overhauling Bosch starter motor

The brush connections need to be soldered

 1 in stock

Speedo sensor with lead and 3 pin plug

Also known as Guzzi ref. 06765400. There are several variants of these sensors, please compare to the sensor on your bike or contact us with a chassis number before ordering

 1 in stock

 883768 MG883768

60/55W H4 P43T headlamp / headlight bulb

This is the more modern H4 bulb with three tabs . Also known as Guzzi ref. 292723

 1 in stock

 93450232 GU93450232 93 45 02 32
 9345 0232 9345.0232 93.45.02.32